RS-15787Community server
nameserver
Offline 77.222.107.65:28015 checked 19d ago
Players
Every five minutes, from the Steam server list.
Hourly average and peak, UTC.
Daily average and peak, UTC.
Server performance
48 hours: hourly readings. 30 to 90 days: one point a day, with the day's average and lowest fps, most entities and most memory. From asking the server directly; low fps and a climbing entity count mean lag.
Rank
Top 71% of all ranked servers. Ranked on player hours over the last seven days.
Wipe schedule
Not enough wipes seen yet to tell when the next one is. Every server wipes at the monthly force wipe.
Wipes
| Wiped | Peak | Crowd | Lasted | Players before |
|---|---|---|---|---|
| No wipe seen yet. | ||||
Peak: the most players in the first 48 hours. Crowd: whether every day of the wipe kept at least half that peak, or the day it fell below. A new world less than six hours after a wipe is a restart, not a wipe of its own.
Similar servers
The same kind of game, then region, group limit, rate and wipes.
Quick answers
From the figures on this page.
Population
How many players are usually on nameserver?
nameserver is offline at this moment; the last signal was 19 days 8 hours ago.
What is the ranking of nameserver?
Ranked #15,787 on seven-day player hours, nameserver is in the top 71% of all ranked servers.
Server tags and lists
Where does nameserver appear among the Top Rust Servers lists and filters?
On these Top Rust Servers lists you will find nameserver: Best Rust community servers. These are the filters that bring it up on the server list: Type: Community (not modded, not official) and No plugins at all; Group limit: 5 or more.
How should you read the tags on nameserver?
The game's server browser reads the tags that nameserver publishes: gmrust (Game mode): Survival follows the standard Rust ruleset; mp5 (Max players): It has 5 slots; ts8 (Group limit): At most 8 per team, as standard in the game; v2633 (Protocol): To join, your game must be on protocol 2633; cs165217 (Build): Game build: 165217; ptrak (Networking): Network layer: RakNet, the standard for the game; $r? (Region code): The region code is left blank. Shown at the top of this page, and also in the tags: its players now, its queue, and the time its world was made.
Rules, settings, and map
Which map is running on nameserver?
nameserver uses a procedural map, which the game generates.
What does nameserver run for rules and settings?
No gather rate is given in the name nameserver. Groups use the default maximum of 8 players. It runs survival, gather, build and raid in the standard game. Player versus player combat and raiding are enabled. A community server, it is found under the Community tab. VAC anti-cheat is inactive.
Server info
What version is nameserver running?
nameserver uses Rust network protocol 2633 and build 165217 with Windows as its system. Your game needs the same protocol to connect; Steam takes care of updating it.
Where can nameserver be found?
A region is not published by nameserver. What Top Rust Servers shows is where a server says it is, not where the machine stands, which it does not look up. It answers at 77.222.107.65:28015.
What is the uptime of nameserver?
nameserver is offline now; the last time it was seen was 19 days 8 hours ago. It spent 0 of the last 168 hours online across 7 days, giving 0% uptime. It was first observed by Top Rust Servers on 18 September 2026.
Wipe cycle
When does nameserver wipe?
Too few wipes are recorded for nameserver to establish a rhythm. The monthly force wipe applies to every Rust server; the next one is on Thursday 5 November at 19:00 UTC. Its world was last replaced 25 days 10 hours ago.
Joining the server
What are the steps to join nameserver?
To connect manually, open the console with F1 and type client.connect 77.222.107.65:28015. Or click Launch Rust on this page to open Rust through Steam and connect directly.